Stainless Steel Three Cylinder Industrial Drying Equipment For Mixed Mortor
Equipment Introduction:
Stainless steel three cylinder industrial drying equipment improves the internal structure on the basis of
single drum dryer, the pre drying of wet material is added before getting into the dryer and prolong the
drying time of wet material in the dryer. It is widely used in various industries’ slag, clay, coal, iron ore
powder, ore powder, and dry mixed mortar, yellow sand and other mixed materials.
Performance Characteristics:
1. Stainless steel three cylinder industrial drying equipment can prevent from acid/alkali corrosion and
iron contamination.
2. Sizes of lump materials, particles, and powders are less than 20mm can be dried.
3. Gear driving is not required and it’s directly driven by roller, with higher mechanical efficiency.
4. Without the phenomenon of air leakage, the sealing difficulty is totally solved, and the installation can
be finished within a few hours.
5. 50% of area covers has been reduced compared with the single drum dryer, and land investment
reduced by 50%, power consumption reduced by 60%.
6. Final moisture indicators can be regulated easily according to the request.
7. The temperature of discharged material is < 50 ℃, which can be directly conveyed into the storage
silo, needless to cool down in the cooling shed.
Working Principle:
Materials get into the internal rotary drum from the feeding device, to realize the downstream drying,
materials are lifted up and down constantly by the inner layer lifting plates and the heat exchange is
realized under the form of spiral moving, materials move to the other side of the inner cylinder and then
get into the middle cylinder, and materials are lifted up and moved forward in the middle cylinder, by the
way of two steps forward and one step back, materials absorb the heat both coming from the inner
cylinder and the middle cylinder, meanwhile, the drying time is prolonged, and materials reach optimum
drying status at this stage. Material move the other end of the middle cylinder and then get into the
outer cylinder, the dried materials are quickly discharged from the cylinder under the function of hot
wind.
Technical Parameters:
| Model | Cylinder data | Capacity(t/h) | Cylinder rotary speed (r/min) | Power (kW) |
| Outer cylinder diameter (m) | Outer cylinder length(m) | Cylinder volume(m3) | River sand | Fly ash | Slag |
| S6203 | 1.6 | 1.8 | 3.6 | 2-3 | 1-2 | 1-2 | 3-10 | 4 |
| S6205 | 2 | 2 | 6.28 | 4-5 | 2-3 | 3-4 | 3-10 | 5.5 |
| S6210 | 2.2 | 2.5 | 9.5 | 8-10 | 4-5 | 6-8 | 3-10 | 7.5 |
| S6215 | 2.5 | 2.8 | 13.7 | 12-15 | 7-8 | 10-12 | 3-10 | 11 |
| 2×4 | 2 | 4 | 12.56 | 8-12 | 4-6 | 8-10 | 3-10 | 3×2 |
| 2×5 | 2 | 5 | 15.7 | 12-15 | 6-7 | 10-13 | 3-10 | 4×2 |
| 2×6 | 2 | 6 | 18.84 | 20-25 | 10-17 | 20-27 | 3-10 | 7.5×2 |
| 2.2×4.5 | 2.2 | 4.5 | 17.09 | 14-18 | 7-9 | 12-15 | 3-10 | 5.5×2 |
| 2.5×6 | 2.5 | 6.5 | 31.89 | 23-28 | 10-13 | 20-22 | 3-10 | 5.5×4 |
| 2.7×7 | 2.7 | 7 | 40.5 | 30-35 | 20-25 | 27-45 | 3-10 | 7.5×4 |
| 2.8×6 | 2.8 | 6 | 36.9 | 30-35 | 15-18 | 25-30 | 3-10 | 5.5×4 |
| 3×6 | 3 | 6 | 42.39 | 35-40 | 18-20 | 32-35 | 3-10 | 7.5×4 |
| 3×7 | 3 | 7 | 49.46 | 40-45 | 20-25 | 35-40 | 3-10 | 7.5×4 |
| 3.2×7 | 3.2 | 7 | 56.26 | 45-50 | 25-30 | 40-45 | 3-10 | 11×4 |
| 3.2×8 | 3.2 | 8 | 64.3 | 50-55 | 30-35 | 45-50 | 3-10 | 11×4 |
| 3.6×8 | 3.6 | 8 | 81.38 | 60-70 | 35-40 | 60-65 | 3-10 | 15×4 |
| 3.8×9 | 3.8 | 9 | 102 | 70-80 | 40-45 | 70-75 | 3-10 | 15×4 |
| 4×10 | 4 | 10 | 125.6 | 90-100 | 45-50 | 80-90 | 3-10 | 18.5×4 |
| 4.2×8.5 | 4.2 | 8.5 | 117.7 | 80-100 | 45-60 | 80-90 | 3-10 | 18.5×4 |
Product Picture Show :
Product Tags:
|
|
Stainless Steel Three Cylinder Industrial Drying Equipment For Mixed Mortor Images
|
